Page 14 of 22
Posted: Mon Mar 27, 2006 9:16 pm
by I7Iz490N
lol
Posted: Mon Mar 27, 2006 10:39 pm
by palmboy5
eh, aite dawg XD
lol Instead of trying 9x260 I stayed with 10x250 and put all the RAM timings on Auto. Prevoiusly they were set Manually to really really loose timings. My RAM read speed in Everest went from 5550MB/s to 6240MB/s! sweet.
Posted: Tue Apr 11, 2006 2:11 am
by palmboy5
ordered arctic freezer pro 64 & a tube of MX-1 & free newegg sticker....
lol should come friday.. better come friday
Posted: Thu Apr 13, 2006 6:51 pm
by palmboy5
ok it came thursday, lol i think i put it on wrong, alot of the paste was pushed out on my several tries to clamp the damn thing down...
Stock:Freezer
Idle - 48:43
Load - 56:51
ewww lame
Posted: Thu Apr 13, 2006 7:15 pm
by 2005
T_T that means my heat pipe cooler will probably be better then the Freezer 64 PRO.... T_T.
That means Ill have to ebay this fucker off and wait for some more money. Then get the 9500 like i WAS going to..
Posted: Thu Apr 13, 2006 9:02 pm
by palmboy5
ill give it its "200 hours" then see
Posted: Thu Apr 13, 2006 9:57 pm
by palmboy5
Posted: Thu Apr 13, 2006 11:53 pm
by I7Iz490N
lol
Posted: Fri Apr 14, 2006 12:07 am
by palmboy5
no i put the right amount of AS5, its just the thing isnt this small chip like the AXPs, it was a perfect seal of the entire IHS onto the heatsink, no air bubbles, just pulling outwards directly isnt going to work. the ZIF socket only pinches on the CPU pins to hold it in, it isnt exactly superglue strength... its a known problem that ive read other people deal with as well... but i have a question, your P4 also has an IHS, this doesnt happen???
its the carpet of the family room, i rarely venture into the area so i dont really give a shit, not my problem
the rest of the house is hardwood floor anyway
Posted: Fri Apr 14, 2006 12:16 am
by I7Iz490N
lol
Posted: Fri Apr 14, 2006 12:19 am
by palmboy5
lol ok so like when you do im gonna question YOU if the azn nerds did it right when it comes off the same way
Posted: Fri Apr 14, 2006 12:23 am
by palmboy5
http://www.mylilsite.net/images/tolches ... eezer1.jpg
uh, is this normal? the black lever part is like tilted when i tighten it like that
Posted: Fri Apr 14, 2006 1:11 am
by palmboy5
running 10x260 with 1.45V, freezer doing far better than the stock with keeping this from getting hot, its like it wont go beyond 56C load, some kinda 'barrier' maybe that temp finally gets the freezer juices going lol.. with stock my idle would be about 52C LOL
so yeah right now its loading at the same load temp as the stock heatsink when at 10x250 1.35V load
but problem! Prime is failing
Posted: Fri Apr 14, 2006 8:15 am
by 2005
Then its not stable dawg...
Posted: Fri Apr 14, 2006 1:53 pm
by palmboy5
yeah that much is obvious... lol but the one stressing the RAM always fails within 20 seconds rather than like.. 12 minutes.. the RAM timings were not tightened and it was run on a divider that downclocked it, WHY is the RAM one failing earlier??
lol oh yeah and the HD temps are lower after i taped up the holes around the PSU, never understood why it had holes there cuz it kinda just decreases the need for air to be sucked in from the front to cool the HD
